PhysicalDevice/Machine/MachineryECOM/Trunk/DIOS.Dev.Machinery.Motion.Driver/DIOS.Dev.Machinery.Client/deliver/Output/conf/ConfGEN/GenErr.xml

<?xml version="1.0" encoding="utf-8" ?>
<AppSetting>
	<Data key="ECOM_KVMAX" value="KV maximum limit" />
  	<Data key="ECOM_KVMIN" value="KV minimum limit" />
 	<Data key="ECOM_MAMAX" value="MA maximum limit" />
  	<Data key="ECOM_MAMIN" value="MA minimum limit" />
 	<Data key="ECOM_MSMAX" value="MS maximum limit" />
  	<Data key="ECOM_MSMIN" value="MS minimum limit" />
 	<Data key="ECOM_MASMAX" value="MAS maximum limit" />
  	<Data key="ECOM_MASMIN" value="MAS minimum limit" />

    <Data key="ECOM_OpenPort_ERR" value="generator Can't Open Port" />
	<Data key="ECOM_CommWarn" value="Check PC communication with SYN and Generator" />
	<Data key="ECOM_CommLost" value="Can't communicate with generator!" />
	<Data key="ECOM_ExceedWnd" value="100:Exceeding the Xray Window!" />
	<Data key="ECOM_ResetFail" value="Reset failed" />
	<Data key="ECOM_TrySendCommand" value="try to send command" />
	<Data key="ECOM_DontGetCommand" value="can't get respond from generator" />
	<Data key="ECOM_CommandReject" value="Technique parameters are not accepted!" />	
	<Data key="ECOM_NotFindXMLFile" value="Can't find file " />	
	<Data key="ECOM_SocketErr" value="Socket init error! " />	
	<Data key="ECOM_NotFindWindow" value="Can't find " />
	
	<Data key="CPI_001" value="Generator CPU EPROM checksum error!" />
	<Data key="CPI_002" value="Generator CPU EEPROM data checksum error!" />
	<Data key="CPI_003" value="Generator CPU NVRAM error!" />
	<Data key="CPI_004" value="Generator CPU Real Time Clock error!" />
	<Data key="CPI_005" value="Main Contactor error!" />
	<Data key="CPI_006" value="Rotor Fault!" />
	<Data key="CPI_007" value="Filament Fault!" />
	<Data key="CPI_008" value="Beam Fault!" />
	<Data key="CPI_009" value="Power Supply Not Ready!" />
	<Data key="CPI_010" value="No KV during exposure  !" />
	<Data key="CPI_011" value="mA during exposure too high!" />
	<Data key="CPI_012" value="mA during exposure too low!" />
	<Data key="CPI_013" value="Manually Terminated Exposure!" />
	<Data key="CPI_014" value="AEC Back-up Timer - Exposure Terminated!" />
	<Data key="CPI_015" value="AEC MAS Exceeded - Exposure Terminated!" />
	<Data key="CPI_016" value="Tomo Back-up Timer - Exposure Terminated!" />
	<Data key="CPI_017" value="Uncalibrated Exposure Parameter!" />
	<Data key="CPI_018" value="Preparation Time-out Error!" />
	<Data key="CPI_019" value="Anode Heat Limit !" />
	<Data key="CPI_020" value="Thermal Switch Interlock #1 Error!" />
	<Data key="CPI_021" value="Thermal Switch Interlock #2 Error!" />
	<Data key="CPI_022" value="Door Interlock Error!" />
	<Data key="CPI_023" value="Collimator Interlock Error!" />
	<Data key="CPI_024" value="Cassette Interlock Error!" />
	<Data key="CPI_025" value="II Safety Interlock Error!" />
	<Data key="CPI_026" value="Spare Input Interlock Error!" />
	<Data key="CPI_027" value="Receptor Time-out Error - Receptor did not respond within time-out!" />
	<Data key="CPI_028" value="Prep Input active during Initialization Phase!" />
	<Data key="CPI_029" value="X-ray Input active during Initialization Phase!" />
	<Data key="CPI_030" value="Fluoro Input active during Initialization Phase !" />
	<Data key="CPI_031" value="Communication Error Remote Fluoro!" />
	<Data key="CPI_032" value="Communication Error Console!" />
	<Data key="CPI_033" value="Lithium Battery Low Voltage Error!" />
	<Data key="CPI_034" value="+12VDC Error!" />
	<Data key="CPI_035" value="-12VDC Error!" />
	<Data key="CPI_036" value="+15VDC Error!" />
	<Data key="CPI_037" value="-15VDC Error!" />
	<Data key="CPI_038" value="Calibration Data Corrupt Error!" />
	<Data key="CPI_039" value="AEC Data Corrupt Error!" />
	<Data key="CPI_040" value="Fluoro Data Corrupt Error!" />
	<Data key="CPI_041" value="Receptor Data Corrupt Error!" />
	<Data key="CPI_042" value="Tube Data Corrupt Error!" />
	<Data key="CPI_043" value="High Voltage Error - KV detected in non x-ray state!" />
	<Data key="CPI_044" value="Invalid Communication Message!" />
	<Data key="CPI_045" value="Communication Message Not Supported!" />
	<Data key="CPI_046" value="Communication Message Not Allowed!" />
	<Data key="CPI_047" value="Fluoro Timer Limit Error!" />
	<Data key="CPI_048" value="Focus Mismatch Error!" />
	<Data key="CPI_049" value="Not Enabled Error!" />
	<Data key="CPI_050" value="Generator Limit Data Corrupt Error!" />
	<Data key="CPI_051" value="AEC Feedback Error (No Feedback Signal Detected)!" />
	<Data key="CPI_052" value="High Small Focus Filament Current Error in Standby!" />
	<Data key="CPI_053" value="High Large Focus Filament Current Error in Standby!" />
	<Data key="CPI_054" value="AEC Reference out of range!" />
	<Data key="CPI_055" value="No Fields Selected in AEC mode!" />
	<Data key="CPI_056" value="No Tube Programmed!" />
	<Data key="CPI_057" value="AEC Stop signal in wrong state!" />
	<Data key="CPI_058" value="Console Back-Up Timer!" />
	<Data key="CPI_059" value="Housing Heat Limit Exceeded!" />
	<Data key="CPI_060" value="High KV Error!" />
	<Data key="CPI_061" value="Low KV Error!" />
	<Data key="CPI_062" value="EXP_SW signal active in standby state!" />
	<Data key="CPI_063" value="Factory Defaults Enabled!" />
	<Data key="CPI_064" value="No Exposure Release !" />
	<Data key="CPI_065" value="Tomo Device Error!" />
	<Data key="CPI_066" value="No Sync Pulse Input!" />
	<Data key="CPI_067" value="Power Supply Duty Cycle Limit!" />
	<Data key="CPI_100" value="Calibration Error - Maximum mA Exceeded!" />
	<Data key="CPI_101" value="Calibration Error - Calibration Data Table Exceeded!" />
	<Data key="CPI_102" value="Calibration Error - Maximum Filament Current Exceeded!" />
	<Data key="CPI_103" value="Calibration Error - Manually Terminated!" />
	<Data key="CPI_104" value="Calibration Error - No mA!" />
	<Data key="CPI_105" value="Calibration Error - Minimum mA not calibrated!" />
	<Data key="CPI_200" value="Anode Warning Level Exceeded!" />
	<Data key="CPI_201" value="Fluoro Timer Warning Level Exceeded!" />
	<Data key="CPI_202" value="Generator KW Limit!"/>
	<Data key="CPI_203" value="Generator KV Limit!"/>
	<Data key="CPI_204" value="Generator MA Limit!"/>
	<Data key="CPI_205" value="Generator MS Limit!"/>
	<Data key="CPI_206" value="Generator MAS Limit!"/>
	<Data key="CPI_207" value="Tube KW Limit!"/>
	<Data key="CPI_208" value="Tube KV Limit!"/>
	<Data key="CPI_209" value="Tube MA Limit!"/>
	<Data key="CPI_210" value="Tube MAS Limit!"/>
	<Data key="CPI_211" value="Calibration Limit, Selected Parameter not Calibrated!" />
	<Data key="CPI_212" value="Generator AEC Density Limit!" />
	<Data key="CPI_213" value="Invalid Communication Parameter!" />
	<Data key="CPI_214" value="Housing Heat Warning!" />
	<Data key="CPI_215" value="CT Termination Input Wrong State!" />
	<Data key="CPI_216" value="Deselect Tomo Table!" />
	<Data key="CPI_217" value="Select Tomo Angle!" />
	<Data key="CPI_218" value="Invalid Tomo Angle!" />
	<Data key="CPI_219" value="Generator PPS Limit!" />
	<Data key="CPI_220" value="Generator Power Supply Duty Cycle Warning!" />
	
	<Data key="SDC_ER_001" value="No Communication with HTC PCB during Initialization Phase!" />
	<Data key="SDC_ER_002" value="No Communication with Fluoro CPU PCB"/>
	<Data key="SDC_ER_003" value="All workstations have configured as tube = 0"/>
	<Data key="SDC_ER_004" value="Generator Internal Preparation Signal Active without Prep Console Command"/>
	<Data key="SDC_ER_005" value=" Fluoro Input Signal Active @ Start-Up or in a Non-Allowed Workstation"/>
	<Data key="SDC_ER_006" value="Prep Inputs or X-Ray Inputs active during Initialization Phase"/>
	<Data key="SDC_ER_007" value="Wrong Tube number for X-ray Tube-1."/>
	<Data key="SDC_ER_008" value="Wrong Tube number for X-ray Tube-2."/>
	<Data key="SDC_ER_009" value="Arcing on the High Voltage Circuit or HV Inverter Overheated."/>
	<Data key="SDC_ER_010" value="EEPROM Corrupted in HT Controller PCB. Or Non-Initialized in ATP Console PCB. Or New ATP Console EPROM has been Installed"/>
	<Data key="SDC_ER_011" value="No Voltage Detection in the Capacitor Bank of the Generator Cabinet"/>
	<Data key="SDC_ER_012" value="The mA Read in the Generator during an Exposure is Out of Range"/>
	<Data key="SDC_ER_013" value="No kVp during Exposure"/>
	<Data key="SDC_ER_014" value="Generator Internal Exposure Signal Active without X-ray Exposure Console Command."/>
	<Data key="SDC_ER_015" value="No Current Detection on Filament Circuit"/>
	<Data key="SDC_ER_016" value="Selected mA, kVp or kW of the Exposure Selection is not correct"/>
	<Data key="SDC_ER_017" value="No Communication with HTC PCB during Normal Operation"/>
	<Data key="SDC_ER_018" value="Rotor not Running or Detected to be Running without Order"/>
	<Data key="SDC_ER_019" value="mA Detected without Exposure Command"/>
	<Data key="SDC_ER_020" value="kV Detected without Exposure Command."/>
	<Data key="SDC_ER_021" value="Wrong Tube 1 Selection."/>
	<Data key="SDC_ER_022" value="Wrong Tube 2 Selection."/>
	<Data key="SDC_ER_023" value="Last Calibration Data not Stored"/>
	<Data key="SDC_ER_024" value="Bucky not Detected to be moving"/>
	<Data key="SDC_ER_025" value="Critical battery level."/>
	<Data key="SDC_ER_026" value="Voltage failure."/>
	<Data key="SDC_ER_027" value="Failure in ATP Console EPROM."/>
	<Data key="SDC_ER_028" value=""/>
	<Data key="SDC_ER_029" value=""/>
	<Data key="SDC_ER_030" value=""/>
	<Data key="SDC_ER_031" value=""/>
	<Data key="SDC_ER_032" value=""/>
	<Data key="SDC_ER_033" value="Communication Failure between PC and Generator."/>
	<Data key="SDC_ER_034" value="Technique error."/>
	<Data key="SDC_ER_035" value="Door Is Open."/>
	<Data key="SDC_ER_036" value="Thermal Switch Open"/>
	<Data key="SDC_ER_037" value="Tube Overload."/>
	<Data key="SDC_ER_038" value=""/>
	<Data key="SDC_ER_039" value=""/>
	<Data key="SDC_ER_040" value=""/>
	<Data key="SDC_ER_041" value="Communication failure between Tube 1 Dosemeter and Generator"/>
	<Data key="SDC_ER_042" value="AutoTest Error on Tube 1 Dosemeter"/>
	<Data key="SDC_ER_043" value="Tube 1 Ion Chamber Status Check Error"/>
	<Data key="SDC_ER_044" value="Communication failure between Tube 2 Dose meter and Generator"/>
	<Data key="SDC_ER_045" value="AutoTest Error on Tube 2 Dose meter"/>
	<Data key="SDC_ER_046" value="Tube 2 Ion Chamber Status Check Error"/>
	<Data key="SDC_ER_047" value="Wrong dosemeter format"/>
	<Data key="SDC_ER_048" value="Collimator Error."/>
	<Data key="SDC_ER_049" value="HU lower than 20%."/>
	<Data key="SDC_ER_050" value="Exposure Interrupted by the Operator!" />
        <Data key="SDC_ER_051" value="Control DRAC PCB Failure in Rom CHECKSUM"/>
	<Data key="SDC_ER_052" value="Control DRAC PCB Failure in RAM"/>
	<Data key="SDC_ER_053" value="Insufficient Voltage in DC BUS for 220 VAC"/>
	<Data key="SDC_ER_054" value="Insufficient Voltage in DC BUS for 380/480 VAC."/>
	<Data key="SDC_ER_055" value="Excessive Voltage in DC BUS for 480 VAC"/>
	<Data key="SDC_ER_056" value=""/>
	<Data key="SDC_ER_057" value=""/>
	<Data key="SDC_ER_058" value="Excessive current in main winding during acceleration to 3300 RPM"/>
	<Data key="SDC_ER_059" value="Excessive current in auxiliary winding during acceleration to 3300 RPM"/>
	<Data key="SDC_ER_060" value="Insufficient current in auxiliary winding during acceleration to 3300 RPM"/>
	<Data key="SDC_ER_061" value="Insufficient current in main winding during acceleration to 3300 RPM."/>
	<Data key="SDC_ER_062" value="Excessive current in main winding during acceleration to 10000 RPM"/>
	<Data key="SDC_ER_063" value="Excessive current in auxiliary winding during acceleration to 10000 RPM"/>
	<Data key="SDC_ER_064" value="Insufficient current in auxiliary winding during acceleration to 10000 RPM"/>
	<Data key="SDC_ER_065" value="Insufficient current in main winding during acceleration to 10000 RPM"/>
	<Data key="SDC_ER_066" value="Excessive current in main winding running at 3300 RPM"/>
	<Data key="SDC_ER_067" value="Excessive current in auxiliary winding running at 3300 RPM"/>
	<Data key="SDC_ER_068" value="Insufficient current in auxiliary winding running at 3300 RPM"/>
	<Data key="SDC_ER_069" value="Insufficient current in main winding running at 3300 RPM"/>
	<Data key="SDC_ER_070" value="Excessive current in main winding running at 10000 RPM" />
        <Data key="SDC_ER_071" value="Excessive current in auxiliary winding running at 10000 RPM."/>
	<Data key="SDC_ER_072" value="Insufficient current in auxiliary winding running at 10000 RPM"/>
	<Data key="SDC_ER_073" value="Insufficient current in main winding running at 10000 RPM"/>
	<Data key="SDC_ER_074" value="Excessive current in main winding braking at 3300 RPM."/>
	<Data key="SDC_ER_075" value="Excessive current in auxiliary winding braking at 3300 RPM"/>
	<Data key="SDC_ER_076" value="Insufficient current in auxiliary winding braking at 3300 RPM"/>
	<Data key="SDC_ER_077" value="Insufficient current in main winding braking at 3300 RPM."/>
	<Data key="SDC_ER_078" value="Excessive current in main winding braking at 10000 RPM"/>
	<Data key="SDC_ER_079" value="Excessive current in auxiliary winding braking at 10000 RPM"/>
	<Data key="SDC_ER_080" value="Insufficient current in auxiliary winding braking at 10000 RPM"/>
	<Data key="SDC_ER_081" value="Insufficient current in main winding braking at 10000 RPM"/>
	<Data key="SDC_ER_082" value="X-ray Tube Selection Signal is not correct in the Control DRAC PCB"/>
	<Data key="SDC_ER_083" value="Excessive current in main or auxiliary winding in DC Brake"/>
	<Data key="SDC_ER_084" value="X-ray Tube Selection Signal is not correct in the Control DRAC PCB"/>
	<Data key="SDC_ER_085" value="X-ray Tube Selection Signal is not correct in the Control DRAC PCB"/>
	<Data key="SDC_ER_086" value="X-ray Tube Selection Signal is not correct in the Control DRAC PCB"/>
	<Data key="SDC_ER_087" value="Insufficient current in common wire during acceleration to 3300 RPM"/>
	<Data key="SDC_ER_088" value="Insufficient current in common wire during running to 3300 RPM"/>
	<Data key="SDC_ER_089" value="Insufficient current in common wire during acceleration to 10000 RPM"/>
	<Data key="SDC_ER_090" value="Insufficient current in common wire during running to 10000 RPM" />
  	<Data key="SDC_ER_091" value="Incorrect signal measure in I PRINC (CH2)."/>
	<Data key="SDC_ER_092" value="Incorrect signal measure in I AUX (CH3)."/>
	<Data key="SDC_ER_093" value="Incorrect signal measure in I COM (CH4)."/>
	<Data key="SDC_ER_098" value="Service Mode is enabled"/>
	
	<Data key="SDC_WN_01" value="MAS_REGUL"/>
	<Data key="SDC_WN_02" value="Maximum KJ"/>
	<Data key="SDC_WN_03" value="Minimum KVP Generator"/>
	<Data key="SDC_WN_04" value="Maximum KVP Generator"/>
	<Data key="SDC_WN_05" value="Minimum MA Generator"/>
	<Data key="SDC_WN_06" value="Maximum MA Generator"/>
	<Data key="SDC_WN_07" value="Minimum MS Generator"/>
	<Data key="SDC_WN_08" value="Maximun MS Generator"/>
	<Data key="SDC_WN_09" value="Minimum MAS Generator"/>
	<Data key="SDC_WN_10" value="Maximun MAS Generator"/>
	<Data key="SDC_WN_11" value="Maximum KW Generator"/>
	<Data key="SDC_WN_12" value="Maximum KVP Tube"/>
	<Data key="SDC_WN_13" value="Space Charge"/>
	<Data key="SDC_WN_14" value="Instant KW"/>
	<Data key="SDC_WN_15" value="KW_PROTECT"/>
	<Data key="SDC_WN_16" value="MAS 3P"/>
	<Data key="SDC_WN_17" value="HCF Mode"/>
	<Data key="SDC_WN_18" value="TOMO_AUTO"/>
	<Data key="SDC_WN_19" value="MIN_MA_MS"/>
	<Data key="SDC_WN_20" value="MAX_MA_MS"/>
	<Data key="SDC_WN_21" value="No Digital Workstation"/>
	<Data key="SDC_WN_22" value="Parameters Adjusted"/>
	<Data key="SDC_WN_23" value="Min Max MA Capacitor"/>
	<Data key="SDC_WN_24" value="Min Max MAS Capacitor"/>
	<Data key="SDC_WN_25" value="Critical battery level"/>
	<Data key="SDC_WN_26" value="Battery High"/>


	<Data key="SDC_WN_DL0" value="Door Open Led Indicator Off"/>
	<Data key="SDC_WN_EL0" value="Technique Error Led Indicator Off"/>
	<Data key="SDC_WN_GL0" value="Generator Overload Led Indicator Off"/>
	<Data key="SDC_WN_HL0" value="Overheat Led Indicator Off"/>
	<Data key="SDC_WN_RL0" value="Rotor Error Led Indicator Off"/>
	<Data key="SDC_WN_TL0" value="Tube Overload Led Indicator Off"/>
	<Data key="SDC_WN_DL1" value="Door Open Led Indicator On"/>
	<Data key="SDC_WN_EL1" value="Technique Error Led Indicator On"/>
	<Data key="SDC_WN_GL1" value="Generator Overload Led Indicator On"/>
	<Data key="SDC_WN_HL1" value="Overheat Led Indicator On"/>
	<Data key="SDC_WN_RL1" value="Rotor Error Led Indicator On"/>
	<Data key="SDC_WN_TL1" value="Tube Overload Led Indicator On"/>
	<Data key="SDC_WN_AOF1" value="The X Ray unit has not been used for 30 min. If you want to connect it to the power source,please click here. It will shutdown in "/>
	<Data key="SDC_WN_OFF" value="If you want to shutdown PC,please click 'OK'. If not,please turn the key to ON and click 'Cancel'. Please place the Arm in parking position. It will shutdown in "/>
	<Data key="SDC_PRE_1" value="Selected position accepted"/>
	<Data key="SDC_PRE_2" value="Selected position rejected, position cannot be reached"/>
	<Data key="SDC_PRE_3" value="Moving to pre-programmed position"/>
	<Data key="SDC_PRE_4" value="Auto position movement stopped"/>
	<Data key="SDC_PRE_5" value="Auto position movement aborted"/>
	<Data key="SDC_PRE_6" value="Pre-programmed position reached"/>
	<Data key="SDC_PRE_7" value="Pre-programmed position reached, but modified by the user"/>
	<Data key="SDC_PRE_8" value="Program not selected"/>
	
	<Data key="SDC_AR_1" value="Gen not enough dose"/>
	<Data key="SDC_AR_2" value="Gen Wrong AEC parameter selection"/>
	
	<Data key="SDC_DualEnery_01" value="First exposure can be made, but not second exposure. Dual Energy not active" />
  	<Data key="SDC_DualEnery_00" value="No exposures can be made. Tube rating exceeded for each exposure or not enough HU. Dual Energy not active." />
  	<Data key="SDC_AEC_NOFIELD" value="No AEC Field selected"/>
	
	<Data key="SDC_WM_0" value="Horizontal interlock for the workstation"/>
	<Data key="SDC_WM_1" value="No interlock for the workstation"/>
	<Data key="SDC_WM_2" value="Vertical interlock for the workstation"/>
	<Data key="SDCMX_WN_001" value="Generator power limit"/>
	<Data key="SDCMX_WN_002" value="Tube power limit"/>
	<Data key="SDCMX_WN_003" value="Space charge limit"/>
	<Data key="SDCMX_WN_004" value="kVp range limit"/>
	<Data key="SDCMX_WN_005" value="mAs range limit"/>
	<Data key="SDCMX_WN_006" value="mA range limit"/>
	<Data key="SDCMX_WN_007" value="mS range limit"/>
	<Data key="SDCMX_WN_008" value="Focus change inhibit"/>
	<Data key="SDCMX_WN_009" value="Wrong APR Technique"/>
	<Data key="SDCMX_WN_010" value="Inverter load limit"/>
	<Data key="SDCMX_WN_011" value="Line power too low"/>
	<Data key="SDCMX_WN_012" value="Wrong APR workstation"/>
	<Data key="SDCMX_WN_013" value="PPS range limit"/>
	<Data key="SDCMX_WN_ComTry" value="try to send command"/>
	<Data key="SDCMX_WN_ComLost" value="can't get respond from generator"/>

	<Data key="SDCMX_ER_001" value="Backup timer-I2C error"/>
	<Data key="SDCMX_ER_002" value="Wrong WS configuration error"/>
	<Data key="SDCMX_ER_003" value="No WS configured error"/>
	<Data key="SDCMX_ER_004" value="Fluoro order error"/>
	<Data key="SDCMX_ER_005" value="EXP order error"/>
	<Data key="SDCMX_ER_006" value="Prep order error"/>
	<Data key="SDCMX_ER_007" value="Tube2 model error"/>
	<Data key="SDCMX_ER_008" value="Tube1 model error"/>

	<Data key="SDCMX_ER_010" value="EEProm check error"/>
	<Data key="SDCMX_ER_011" value="Load capacition error"/>
	<Data key="SDCMX_ER_012" value="MA range error"/>
	<Data key="SDCMX_ER_013" value="KVP range error"/>
	<Data key="SDCMX_ER_014" value="KVP ramp error"/>
	<Data key="SDCMX_ER_015" value="Large Fil current range error"/>
	<Data key="SDCMX_ER_016" value="Small Fil current range error"/>
	<Data key="SDCMX_ER_017" value="DC bus range error"/>

	<Data key="SDCMX_ER_019" value="MA without Exp error"/>
	<Data key="SDCMX_ER_020" value="KVP without Exp error"/>

	<Data key="SDCMX_ER_023" value="EEProm error"/>
	<Data key="SDCMX_ER_024" value="Bucky/digital panel error"/>
	<Data key="SDCMX_ER_025" value="Large fil demand error"/>
	<Data key="SDCMX_ER_026" value="Small fil demand error"/>
	<Data key="SDCMX_ER_027" value="Collimator light current range error"/>
	<Data key="SDCMX_ER_028" value="Collimator light current without order error"/>
	<Data key="SDCMX_ER_029" value="Generator overload error"/>
	<Data key="SDCMX_ER_030" value="Corrupt rtc error"/>
	<Data key="SDCMX_ER_031" value="Time stamp check error"/>
	<Data key="SDCMX_ER_032" value="RTC-I2C error"/>
	<Data key="SDCMX_ER_033" value="Communications error"/>
	<Data key="SDCMX_ER_034" value="Exposure timer error"/>

	<Data key="SDCMX_ER_036" value="Presostat error"/>
	<Data key="SDCMX_ER_037" value="Tube overload error"/>
	<Data key="SDCMX_ER_038" value="Chopper error"/>
	<Data key="SDCMX_ER_039" value="Power supply error"/>
	<Data key="SDCMX_ER_040" value="Imbalanced KVP error"/>
	<Data key="SDCMX_ER_041" value="Imbalanced MA error"/>
	<Data key="SDCMX_ER_042" value="Counters check error"/>
	<Data key="SDCMX_ER_043" value="Error log check error"/>
	<Data key="SDCMX_ER_044" value="Digital potentiometer-I2C error"/>
	<Data key="SDCMX_ER_045" value="Multiplexer-I2C error"/>
	<Data key="SDCMX_ER_046" value="Busy bus-I2C error"/>
	<Data key="SDCMX_ER_047" value="Apr lite check error"/>
	<Data key="SDCMX_ER_048" value="Bucky/digital interface error"/>

	<Data key="SDCMX_ER_050" value="Aborted exposure error"/>
	<Data key="SDCMX_ER_051" value="Wrong exposure time error"/>
	<Data key="SDCMX_ER_060" value="Autocal error"/>
	<Data key="SDCMX_ER_095" value="Line power too low error"/>
	<Data key="SDCMX_ER_OverHeat" value="Overheat error"/>
	<Data key="SDCMX_ER_XToOn" value="Turns on X-Ray Key"/>
	<Data key="SDCMX_ER_Tube" value="Tube Overload error"/>
	<Data key="SDCMX_ER_Inverter" value="Inverter Overload error"/>
	<Data key="SDCMX_ER_ComLost" value="033:Can't communicate with generator"/>
	<Data key="SDCMX_ER_ErrrAn" value="RAM memory error"/>
	<Data key="SDCMX_ER_ErrnrAn" value="NON volatile RAM(NVRAM) memory error"/>

	<Data key="SDCMX_ST_001" value="Initialization phase"/>
	<Data key="SDCMX_ST_002" value="Standby"/>
	<Data key="SDCMX_ST_003" value="Preparation"/>
	<Data key="SDCMX_ST_004" value="Exposure"/>
	<Data key="SDCMX_ST_005" value="Fluoro"/>
	<Data key="SDCMX_ST_006" value="Filament Current Calibration"/>
	<Data key="SDCMX_ST_007" value="Unrecoverable Error"/>
	<Data key="SDCMX_ST_008" value="Configuration"/>
	<Data key="SDCMX_ST_009" value="AutoCalibration"/>
	<Data key="SDCMX_ST_010" value="Parameters Calibration"/>
	<Data key="SDCMX_ST_011" value="Recoverable Error"/>
	
	<Data key="SIEMENS_Err0002" value="Internal SW Error"/>
	<Data key="SIEMENS_Err0003" value="Internal SW Error"/>
	<Data key="SIEMENS_Err0006" value="Internal SW Error"/>
	<Data key="SIEMENS_Err0007" value="Parallel Coil Temperature Error"/>
	<Data key="SIEMENS_Err0010" value="Power Supply Error"/>
	<Data key="SIEMENS_Err0012" value="Arcing Error"/>
	<Data key="SIEMENS_Err0013" value="Door Position Error"/>
	<Data key="SIEMENS_Err0017" value="Grid Feedback Signal Error"/>
	<Data key="SIEMENS_Err0018" value="Tube Unit Error"/>
	<Data key="SIEMENS_Err0019" value="Dongle Error"/>
	<Data key="SIEMENS_Err0021" value="Operating Error (engineer)"/>
	<Data key="SIEMENS_Err0022" value="K1 Main Contactor"/>
	<Data key="SIEMENS_Err0023" value="K2 Charger Contactor"/>
	<Data key="SIEMENS_Err0024" value="Intermediate Circuit (UDC) Error"/>
	<Data key="SIEMENS_Err0025" value="Rotating Anode Operating Error"/>
	<Data key="SIEMENS_Err0026" value="HVT Overpressure Error"/>
	<Data key="SIEMENS_Err0029" value="Power Supply Error"/>
	<Data key="SIEMENS_Err0030" value="Console HW Error"/>
	<Data key="SIEMENS_Err0032" value="Real Time Clock Data Error"/>
	<Data key="SIEMENS_Err0033" value="HVT Temperature Sensor Error"/>
	<Data key="SIEMENS_Err0034" value="Safety circuit is closed during bootup"/>
	<Data key="SIEMENS_Err0035" value="kV Plus Over-Voltage Error"/>
	<Data key="SIEMENS_Err0036" value="kV Negative Over-Voltage Error"/>
	<Data key="SIEMENS_Err0037" value="kV Delta Error"/>
	<Data key="SIEMENS_Err0038" value="Tube voltage is out of tolerance"/>
	<Data key="SIEMENS_Err0039" value="Tube current Is out of tolerance"/>
	<Data key="SIEMENS_Err0040" value="Main Inverter, Short Circuit Error (Imax)"/>
	<Data key="SIEMENS_Err0041" value="I_load, UBmax Error"/>
	<Data key="SIEMENS_Err0042" value="XRAY_On Error"/>
	<Data key="SIEMENS_Err0043" value="Tube Configuration Error"/>
	<Data key="SIEMENS_Err0044" value="AEC Chamber Configuration Error"/>
	<Data key="SIEMENS_Err0045" value="High Voltage Cable Configuration Error"/>
	<Data key="SIEMENS_Err0049" value="Heating Learn Routine Error"/>
	<Data key="SIEMENS_Err0050" value="Generator Not Adjusted"/>
	<Data key="SIEMENS_Err0051" value="D115 Connection Error"/>
	<Data key="SIEMENS_Err0055" value="D800 S3 Incorrect Position"/>
	<Data key="SIEMENS_Err0100" value="D470 Error,Error during Exposure, error of the Exposure Focus"/>
	<Data key="SIEMENS_Err0101" value="Internal SW Error"/>
	<Data key="SIEMENS_Err0102" value="D470 Error,Error during Exposure"/>
	<Data key="SIEMENS_Err0103" value="D470 Error,Error during Exposure and Standby, Large Focus error"/>
	<Data key="SIEMENS_Err0104" value="D470 Error,Error during Exposure and Standby, Small Focus error"/>
	<Data key="SIEMENS_Err0106" value="Focus selection error"/>
	<Data key="SIEMENS_Err0109" value="U_DC timeout"/>
	<Data key="SIEMENS_Err0114" value="D470 not connected"/>
	<Data key="SIEMENS_Err0115" value="D800 S4 Incorrect Position"/>
	<Data key="SIEMENS_Err0116" value="Internal SW Error"/>
	<Data key="SIEMENS_Err0171" value="HW Error on D800"/>
	<Data key="SIEMENS_Err0172" value="Inverter Temperature Sensor Error"/>
	<Data key="SIEMENS_Err0177" value="Inverter Error"/>
	<Data key="SIEMENS_Err0190" value="D800 Over temperature"/>
	<Data key="SIEMENS_Err0255" value="Undefined Error"/>
	<Data key="SIEMENS_Err0550" value="Dose Monitoring Error"/>
	<Data key="SIEMENS_Err0700" value="DR-interface protocol error"/>
	<Data key="SIEMENS_Err0701" value="DR-interface protocol error"/>
	<Data key="SIEMENS_Err0702" value="DR-interface protocol error"/>
	<Data key="SIEMENS_Err0703" value="DR-interface protocol error"/>
	<Data key="SIEMENS_Limit_MAS" value="Limit MAS"/>
	<Data key="SIEMENS_Limit_Time" value="Limit Time"/>
    <Data key="SIEMENS_System_NOReady" value="Generator ready and OTC is not ready"/>
    <Data key="SIEMENS_UnknownCommand" value="Generator Unit rejects command as unknown command"/>
	<Data key="SIEMENS_TankTemper_Blow" value="single tank temperature below 60"/>
   	<Data key="SIEMENS_TankTemper_Above" value="single tank temperature above 60"/>
   	
	<Data key="SMAM_ER_000" value="Success"/>
	<Data key="SMAM_ER_001" value="Program fault 1"/>
	<Data key="SMAM_ER_100" value="OVL timeou"/>
	<Data key="SMAM_ER_101" value="PREP released"/>
	<Data key="SMAM_ER_102" value="XRAY released"/>
	<Data key="SMAM_ER_103" value="STARTER fail"/>
	<Data key="SMAM_ER_104" value="PR0 timeout"/>
	<Data key="SMAM_ER_105" value="PR1 timeout"/>
	<Data key="SMAM_ER_106" value="PR2 timeout"/>
	<Data key="SMAM_ER_107" value="XR1 timeout"/>
	<Data key="SMAM_ER_108" value="XR0 timeout"/>
	<Data key="SMAM_ER_109" value="OVC alarm"/>
	<Data key="SMAM_ER_110" value="OVL alarm"/>
	<Data key="SMAM_ER_111" value="Max value"/>
	<Data key="SMAM_ER_112" value="Invalid focus"/>
	<Data key="SMAM_ER_113" value="Min current"/>
	<Data key="SMAM_ER_114" value="Max current"/>
	<Data key="SMAM_ER_115" value="85% missed"/>
	<Data key="SMAM_ER_116" value="Wrong contest"/>
	<Data key="SMAM_ER_117" value="Wrong technique"/>
	<Data key="SMAM_ER_118" value="Out of range"/>
	<Data key="SMAM_ER_119" value="Invalid value"/>
	<Data key="SMAM_ER_120" value="Correlation fail"/>
	<Data key="SMAM_ER_121" value="Potter fail"/>
	<Data key="SMAM_ER_122" value="DAP not present"/>
	<Data key="SMAM_ER_123" value="DAP disabled"/>
	<Data key="SMAM_ER_124" value="DAP error"/>
	<Data key="SMAM_ER_125" value="DAP timeout"/>
	
	<Data key="SMAM_ST_00" value="Initialization Phase"/>
	<Data key="SMAM_ST_01" value="Capacitor charge phase"/>
	<Data key="SMAM_ST_02" value="Waiting PR0 from console"/>
	<Data key="SMAM_ST_03" value="Stand by phase (PR0)"/>
	<Data key="SMAM_ST_04" value="Waiting PR1 from console"/>
	<Data key="SMAM_ST_05" value="Rad Preparation Phase (PR1)"/>
	<Data key="SMAM_ST_06" value="Waiting PR2 from console"/>
	<Data key="SMAM_ST_07" value="Ready for x-ray (PR2)"/>
	<Data key="SMAM_ST_08" value="Waiting XR1 from console"/>
	<Data key="SMAM_ST_09" value="Rad Exposure Phase (XR1)"/>
	<Data key="SMAM_ST_10" value="Post X ray phase XR2"/>
	<Data key="SMAM_ST_11" value="Waiting XR0 from console"/>
	<Data key="SMAM_ST_12" value="End of x-ray (XR0)"/>
	<Data key="SMAM_ST_13" value="Error phase"/>
	
	<Data key="PUK_ER_1" value="Temperature Difference Warning"/>
	<Data key="PUK_ER_2" value="Temperature Switch Warning"/>
	<Data key="PUK_ER_3" value="Contravariant Warning"/>
	<Data key="PUK_ER_4" value="Filament Warning"/>
	<Data key="PUK_ER_5" value="Rotate Anode Warning"/>
	<Data key="PUK_ER_6" value="Small mAs Exposure Timeout Warning"/>
	<Data key="PUK_ER_7" value="Large mAs Exposure Timeout Warning"/>
	<Data key="PUK_ER_8" value="EEPROM Warning"/>
	<Data key="PUK_ER_9" value="No Exposure Signal From Panel"/>
	<Data key="PUK_WN_0" value="Data correct"/>
	<Data key="PUK_WN_1" value="KV Range Limit"/>
	<Data key="PUK_WN_2" value="mAs Range Limit"/>
	<Data key="PUK_WN_3" value="key value invalid"/>
	<Data key="PUK_WN_20" value="CheckSum is invalid"/>
	<Data key="PUK_XrayPre" value="X-ray ready..."/>
	<Data key="PUK_XrayReady" value="X-ray is ready, Please Exposure !"/>
	<Data key="PUK_XrayNotReady" value="X-Ray is not ready !"/>
	<Data key="GEN_CommInterrupt" value="Can't communicate with generator"/>

	<Data key="EMD_100" value="System Fault!" />
  	<Data key="EMD_200" value="System Limit!" />
 	<Data key="EMD_300" value="KV Limit!" />
  	<Data key="EMD_301" value="MA Limit!" />
  	<Data key="EMD_302" value="MS Limit!" />
  	<Data key="EMD_303" value="MAS Limit!" />
  	<Data key="EMD_304" value="Cooling Delay!" />
  	<Data key="EMD_305" value="Backup MAS Limit!" />
  	<Data key="EMD_306" value="KW Limit!" />
  	<Data key="EMD_307" value="Frame Rate or Run Length Limit!" />
  	<Data key="EMD_400" value="Invalid Focus!" />
  	<Data key="EMD_401" value="Invalid Anode Speed!" />
  	<Data key="EMD_402" value="Tube Heat Units Limit!" />
  	<Data key="EMD_403" value="Invalid ION Selection!" />
  	<Data key="EMD_404" value="Tube KV Limit!" />
  	<Data key="EMD_405" value="Tube Filament Limit!" />
  	<Data key="EMD_406" value="Tube KW Limit!" />
  	<Data key="EMD_407" value="Mode Limit!" />

 	<Data key="WAND_WN_001" value="KV maximum limit" />
  	<Data key="WAND_WN_002" value="KV minimum limit" />
 	<Data key="WAND_WN_003" value="MA maximum limit" />
  	<Data key="WAND_WN_004" value="MA minimum limit" />
 	<Data key="WAND_WN_005" value="MS maximum limit" />
  	<Data key="WAND_WN_006" value="MS minimum limit" />

 	<Data key="WAND_ER_1" value="ER 1" />
  	<Data key="WAND_ER_2" value="ER 2" />
 	<Data key="WAND_ER_3" value="ER 3" />
  	<Data key="WAND_ER_4" value="ER 4" />
 	<Data key="WAND_ER_5" value="ER 5" />
  	<Data key="WAND_ER_62" value="ER 62" />
  	  	
  	<Data key="XH_ENERGY_ERR" value="Energy Error" />
  	<Data key="XH_TUBE1_OVER" value="Tube1 temperature over" />
  	<Data key="XH_TUBE2_OVER" value="Tube2 temperature over" />
  	<Data key="XH_TUBE_ERR" value="Tube Error" />
  	<Data key="XH_MAIN_ERR" value="Main power Error" />
  	<Data key="XH_AECEXPOSURETIME_WAR" value="AEC Exposure Timeout Warning" />
  	<Data key="XH_DOOROPEN" value="Door open" />
  	<Data key="XH_STATORFS_ERR" value="Statorfs Error" />
  	<Data key="XH_DOSE_OVER" value="set KV\MA overhigh or overlow" />
  	<Data key="XH_FILAMENT_ERR" value="warm filament error" />
  	<Data key="XH_LARGE_FILFBS_ERR" value="Large FILFBS error" />
  	
  	 <Data key="XH_SMALL_FILFBS_ERR" value="Small FILFBS error" />
  	<Data key="XH_KV_ERR" value="KV error" />
  	<Data key="XH_DRMA_ERR" value="DR MA error" />
  	<Data key="XH_FLOUROMA_ERR" value="Flouro Ma error" />
  	
  	<Data key="PRV_ERR" value="error" />
  	
  	<Data key="KS_Heat_LargeFocus" value="Large Focus Heating..." />
  	<Data key="KS_Heat_SmallFocus" value="Small Focus Heating..." />
  	
  	<Data key="DK_APR" value="SET ECT APR" />
  	
  	<Data key="BROWINER_System_Err" value="System Error,Please check" />
  	
  	<Data key="ALLENGERS_DualEnery_01" value="First exposure can be made, but not second exposure. Dual Energy not active" />
  	<Data key="ALLENGERS_DualEnery_02" value=" No exposures can be made. Tube rating exceeded for each exposure or not enough HU. Dual Energy not active." />

	<Data key="IMD_WN_SetAPR" value="Setting APR. Please Wait" />
	<Data key="IMD_WN_SetAPREnd" value="End setting APR" />
	<Data key="IMD_WN_XrayPre" value="Green light on,X-RAY Prepare" />
	<Data key="IMD_WN_XrayOn" value="Red light on,X-RAY on" />
	<Data key="IMD_WN_XrayExp" value="Yellow light on,X-RAY Exposure" />
	
	<Data key="SEDVET_NOTCONSOLE" value="Can't find SEDECAL GENERATOR CONSOLE" />

	<Data key="REMEDY_001" value="" />
	<Data key="REMEDY_002" value="" />
	<Data key="REMEDY_003" value="Generator CPU EEPROM Data Checksum Error!" />
	<Data key="REMEDY_004" value="Generator CPU Real Time Clock error!" />
	<Data key="REMEDY_005" value="Main Contactor error!" />
	<Data key="REMEDY_006" value="Rotor Fault!" />
	<Data key="REMEDY_007" value="Filament Fault!" />
	<Data key="REMEDY_008" value="" />
	<Data key="REMEDY_009" value="Beam_Cathode Fault!" />
	<Data key="REMEDY_010" value="Beam_Anode Fault!" />
	<Data key="REMEDY_011" value="Beam_INVA Fault!" />
	<Data key="REMEDY_012" value="Beam_INVB Fault!" />
	<Data key="REMEDY_013" value="Beam_KV Fault!" />
	<Data key="REMEDY_014" value="Beam_IR Fault!" />
	<Data key="REMEDY_015" value="Beam KV too low!" />
	<Data key="REMEDY_016" value="Bean kv unbalance!" />
	<Data key="REMEDY_017" value="Inverter is too hot!" />
	<Data key="REMEDY_018" value="Preparation Time-out Error!" />
	<Data key="REMEDY_019" value="" />
	<Data key="REMEDY_020" value="No KV during exposure!" />
	<Data key="REMEDY_021" value="mA during exposure too high!" />
	<Data key="REMEDY_022" value="mA during exposure too low!" />
	<Data key="REMEDY_023" value="Manually Terminated Exposure!" />
	<Data key="REMEDY_024" value="AEC Back-up Timer - Exposure Terminated!" />
	<Data key="REMEDY_025" value="AEC MAS Exceeded - Exposure Terminated!" />
	<Data key="REMEDY_026" value="" />
	<Data key="REMEDY_027" value="Anode Heat Limit!" />
	<Data key="REMEDY_028" value="Thermal Switch Interlock Error!" />
	<Data key="REMEDY_029" value="Door Interlock Error!" />
	<Data key="REMEDY_030" value="" />
	<Data key="REMEDY_031" value="Bucky 1 Not Contact Error!" />
	<Data key="REMEDY_032" value="" />
	<Data key="REMEDY_033" value="Bucky 2 Not Contact Error!" />
	<Data key="REMEDY_034" value="Prep Input active during Initialization Phase!" />
	<Data key="REMEDY_035" value="X-ray Input active during Initialization Phase!" />
	<Data key="REMEDY_036" value="Communication Error Console!" />
	<Data key="REMEDY_037" value="+12VDC Error!" />
	<Data key="REMEDY_038" value="-12VDC Error!" />
	<Data key="REMEDY_039" value="" />
	<Data key="REMEDY_040" value="" />
	<Data key="REMEDY_041" value="" />
	<Data key="REMEDY_042" value="" />
	<Data key="REMEDY_043" value="High Voltage Error - KV detected in non x-ray state!" />
	<Data key="REMEDY_044" value="Invalid Communication Message!" />
	<Data key="REMEDY_045" value="Communication Message Not Supported!" />
	<Data key="REMEDY_046" value="Communication Message Not Allowed!" />
	<Data key="REMEDY_047" value="" />
	<Data key="REMEDY_048" value="Current reception is not enabled!" />
	<Data key="REMEDY_049" value="AEC channel is not enable in current reception!" />
	<Data key="REMEDY_050" value="" />
	<Data key="REMEDY_051" value="AEC Feedback Error (No Feedback Signal Detected)!" />
	<Data key="REMEDY_052" value="High Small Focus Filament Current Error in Standby!" />
	<Data key="REMEDY_053" value="High Large Focus Filament Current Error in Standby!" />
	<Data key="REMEDY_054" value="AEC Reference out of range!" />
	<Data key="REMEDY_055" value="No Fields Selected in AEC mode!" />
	<Data key="REMEDY_056" value="No Tube Programmed!" />
	<Data key="REMEDY_057" value="AEC Stop signal in wrong state!" />
	<Data key="REMEDY_058" value="" />
	<Data key="REMEDY_059" value="" />
	<Data key="REMEDY_060" value="" />
	<Data key="REMEDY_061" value="" />
	<Data key="REMEDY_062" value="" />
	<Data key="REMEDY_063" value="" />
	<Data key="REMEDY_064" value="" />
	<Data key="REMEDY_065" value="" />
	<Data key="REMEDY_066" value="" />
	<Data key="REMEDY_067" value="" />
	<Data key="REMEDY_071" value="Boost filament current error" />
	<Data key="REMEDY_072" value="Preheat filament current error" />
	<Data key="REMEDY_073" value="Film screen is invalid" />
	<Data key="REMEDY_074" value="DC BUS voltage is too higher or too low" />
	<Data key="REMEDY_075" value="Tube count data corrupt" />
	<Data key="REMEDY_100" value="Calibration Error - Maximum mA Exceeded!" />
	<Data key="REMEDY_101" value="Calibration Error - Calibration Data Table Exceeded!" />
	<Data key="REMEDY_102" value="Calibration Error - Maximum Filament Current Exceeded!" />
	<Data key="REMEDY_103" value="Calibration Error - Manually Terminated!" />
	<Data key="REMEDY_104" value="Calibration Error - No mA!" />
	<Data key="REMEDY_105" value="Calibration Error - Minimum mA not calibrated!" />
	<Data key="REMEDY_106" value="Generator Limit, Selected Parameter Not calibrated!" />
	<Data key="REMEDY_107" value="pre-charge relay fault!" />
	<Data key="REMEDY_108" value="large filament set parameter is more than max. filament current!" />
	<Data key="REMEDY_109" value="small filament set parameter is more than max. filament current!" />
	<Data key="REMEDY_200" value="Anode Warning Level Exceeded!" />
	<Data key="REMEDY_201" value="" />
	<Data key="REMEDY_202" value="Generator KW Limit!"/>
	<Data key="REMEDY_203" value="Generator KV Limit!"/>
	<Data key="REMEDY_204" value="Generator MA Limit!"/>
	<Data key="REMEDY_205" value="Generator MS Limit!"/>
	<Data key="REMEDY_206" value="Generator MAS Limit!"/>
	<Data key="REMEDY_207" value="Tube KW Limit!"/>
	<Data key="REMEDY_208" value="Tube KV Limit!"/>
	<Data key="REMEDY_209" value="Tube MA Limit!"/>
	<Data key="REMEDY_210" value="Tube MAS Limit!"/>
	<Data key="REMEDY_211" value="" />
	<Data key="REMEDY_212" value="Generator AEC Density Limit!" />
	<Data key="REMEDY_213" value="Invalid Communication Parameter!" />
	<Data key="REMEDY_214" value="Housing Heat Warning2!" />
	<Data key="REMEDY_214" value="Housing Heat Warning!" />
	<Data key="REMEDY_215" value="CT Termination Input Wrong State!" />
	<Data key="REMEDY_216" value="Deselect Tomo Table!" />
	<Data key="REMEDY_217" value="Select Tomo Angle!" />
	<Data key="REMEDY_218" value="Invalid Tomo Angle!" />
	<Data key="REMEDY_219" value="Generator PPS Limit!" />
	<Data key="REMEDY_220" value="Generator Power Supply Duty Cycle Warning!" />

	<Data key="MIKASAECOM_ER_1" value="The filament temperature is too high"/>
	<Data key="MIKASAECOM_ER_2" value="The filament current is too high"/>
	<Data key="MIKASAECOM_ER_3" value="The filament voltage is too high"/>
	<Data key="MIKASAECOM_ER_4" value="DR cable not connect"/>
	<Data key="MIKASAECOM_ER_5" value="RXCOMTIME callback out time"/>
	<Data key="MIKASAECOM_ER_6" value="RXREQTIME recover failed after Exposure done"/>
	<Data key="MIKASAECOM_ER_7" value="Not press hand switch, DR output"/>
	<Data key="MIKASAECOM_ER_8" value="Exposure Interrupted by the Operator!"/>
	<Data key="MIKASAECOM_ER_9" value="Exposure time too long"/>
	<Data key="MIKASAECOM_ER_10" value="MAIN and SUB handshake error"/>
	<Data key="MIKASAECOM_ER_11" value="MAIN and SUB version don't match"/>
	<Data key="MIKASAECOM_ER_12" value="Exposure Technique Selection error"/>
	<Data key="MIKASAECOM_ER_13" value="Focus Selection error"/>
	<Data key="MIKASAECOM_ER_14" value="Generator function Mode error"/>

	<Data key="MIKASAECOM_WN_1" value="Generator KW Limit!"/>
	<Data key="MIKASAECOM_WN_2" value="Generator KV Limit!"/>
	<Data key="MIKASAECOM_WN_3" value="Generator MA Limit!"/>
	<Data key="MIKASAECOM_WN_4" value="Generator MS Limit!"/>
	<Data key="MIKASAECOM_WN_5" value="Generator MAS Limit!"/>
	<Data key="MIKASAECOM_WN_6" value="Tube KW Limit!"/>
	<Data key="MIKASAECOM_WN_7" value="Tube KV Limit!"/>
	<Data key="MIKASAECOM_WN_8" value="Tube MA Limit!"/>
	<Data key="MIKASAECOM_WN_9" value="Tube MAS Limit!"/>
</AppSetting>